Light, torsion-resistant clamps made of hammer-finished, cast aluminium. Offset base, steel screw and ball-jointed swivel pad.
From: 17,00 €
5-piece set: 1x 705890, -92, -93, 2x 705891 Light, torsion-resistant clamps made of hammer-finished, cast aluminium. Offset base, steel screw and ball-jointed swivel pad. Set includes 705890, 705891, 705892, 705893. No. 705891 is included twice. Set contains the following products: 705890 Aluminium Repair Clamp, Jaw Depth 85 mm 705891 ...
125,00 € excl. VAT
Bridge assembly clamp with adjustable depth and 30 mm thread spindle. Felt cushioned bridge member, with adjustable screws to comply with any individual bridge profile. Material Steel, Instrument Guitar, Jaw depth 100 – 145 mm, Weight 1.685 g
98,00 € excl. VAT
Jaw opening: 500 mm Gluing clamp for guitar-making. Low depth to prevent bending of the thin plates while gluing the center-joint . Material Steel, Length 625 mm, Instrument Guitar, Jaw depth 30 mm
66,00 € excl. VAT
For gluing linings and edges. Brass, finely machined. Depth 18 mm, opening 15 mm.
9,00 € excl. VAT
The ideal tool for removing stubborn endbuttons and for holding endbuttons while shaping their shafts. Screw clamp with leather-lined endbutton holder. Brass body with knurled surface, Ø 25 mm. Fits all violin and viola endbuttons which have a maximum neck-Ø of 9.5 mm. Ø 25 mm. Fits violin and ...
11,00 € excl. VAT
For repair of top cracks through f-hole without opening of the instrument. Adjustable needle simply holds the cleat and enables to glue it in a proper position on the crack inside the instrument. Stainless steel body diameter 4.8 mm. Depth 30/50/75/100 mm. Opening 30 mm.
77,00 € excl. VAT
For an even distribution of clamping pressure when gluing fingerboards in place. 2-piece sets, (for fingerboard and neck) made of rosewood.
9,00 € excl. VAT
For repairing edges (better pressure distribution). The 3 arms rotate around the central joint. Herdim® Crack ClampsMade in GermanyThese clamps are ideal for repairing cracks in stringed instrument tops and backs. They have a large array of applications due to their light weight and adjustable jaw openings.The movable clamping ...
From: 70,00 €
The new Herdim aluminium crack clamps not only are extremely lightweight, they also show twisting clamping jaws which are flexible and perfectly accommodate to the contours of the instrument. The risk of chipping the edges when repairing a table or bottom crack is minimized. The non-slip jaws hold the ...
39,00 €
The new Herdim aluminium crack clamps not only are extremely lightweight, they also show twisting clamping jaws which are flexible and perfectly accommodate to the contours of the instrument. So the risk of chipping the edges when repairing a table or bottom crack is minimized. The non-slip jaws hold ...
147,00 € excl. VAT
Herdim® Crack ClampsMade in GermanyThese clamps are ideal for repairing cracks in stringed instrument tops and backs. They have a large array of applications due to their light weight and adjustable jaw openings.The movable clamping jaw (1) can be easily set to the desired length. The clamping pad (2) ...
From: 40,00 €
Lightweight aluminum clamp for cleating cracks. With ball-bearing jointed swivel cap. Opening 55 mm, depth 125 mm, weight approx. 75 g.
24,00 € excl. VAT
Small specialty tool for gluing cracks. Galvanized steel (can be tightened with a M2 hex wrench, not included). The blocks lining the crack are cut off after gluing.Opening 12 mm, Depth 5 mm. Opening 12 mm, depth 5 mm.
4,00 € excl. VAT
For repairing a removed top (clamping pressure can be applied from above and below). Herdim® Crack ClampsMade in GermanyThese clamps are ideal for repairing cracks in stringed instrument tops and backs. They have a large array of applications due to their light weight and adjustable jaw openings.The movable clamping ...
From: 68,00 €
For repairing cracks close to the edges. Exceptionally strong titanium colored aluminum alloy body. Precision double guide rods, adjustable base height, direct pressure application upon closure. Opening 8 mm, depth 19 mm, weight 113 g.
105,00 € excl. VAT
With one thin pad, for cracks near the f-holes. Applied between the edge and the f-hole. Herdim® Crack ClampsMade in GermanyThese clamps are ideal for repairing cracks in stringed instrument tops and backs. They have a large array of applications due to their light weight and adjustable jaw openings.The ...
From: 38,00 €
With two thin pads, for cracks between the f-holes. Applied between the f-holes. Herdim® Crack ClampsMade in GermanyThese clamps are ideal for repairing cracks in stringed instrument tops and backs. They have a large array of applications due to their light weight and adjustable jaw openings.The movable clamping jaw ...
38,00 € excl. VAT
Special spreading tool for lifting and repairing damaged f-hole flaps (fits through the f-hole). Can also be used to measure sound post length.
From: 16,00 €
For gluing the purfling from the exterior of the instrument. Zinc-coated steel.Depth 15 mm, Ø 5 mm. Opening 16-28 mm, depth 15 mm, Diameter 5 mm.
5,00 € excl. VAT
For gluing the ribs to the lower block without disassembling the instrument. Once inserted into the instrument, the steel pivot automatically flips into the cross position as the screw is turned. Rosewood body lined with cork.
From: 6,00 €
Made in GermanyLightweight, precision clamps for repairing musical instruments and other fine handcrafted objects. Forged-steel frame with galvanised surfaces. Fast-action brass screw with ball-jointed swivel rubber coated pad and removable knurled knob. To protect varnished surfaces, special silicone pads are available as accessories. Jaw depth 22 mm, Jaw opening ...
From: 19,00 €
7-piece set, 1 x No. 735702, -04, -07, -14, -15, -18, -19. Made in GermanyLightweight, precision clamps for repairing musical instruments and other fine handcrafted objects. Forged-steel frame with galvanised surfaces. Fast-action brass screw with ball-jointed swivel rubber coated pad and knurled knob. Set contains the following products: 735702 ...
147,00 € excl. VAT
For re-gluing rib corners. After attaching the clamp to the rib corner area, pressure can be applied directly to both sides of the rib corner using the small perpendicular spindles. Opening 50 mm, 4 spindles.
From: 150,00 €
- 1
- 2
Showing 1–24 of 31 results